Solenoid valve in the selection of matters needing attention
One: Applicability
The fluid in the tubing must match that of the media in the selected solenoid valve model.
The temperature of the fluid must be less than the calibrated temperature of the selected solenoid valve.
Solenoid valves allow the viscosity of liquids to be generally below 20CST, and should be indicated when more than 20CST.
Working pressure difference, the maximum pressure difference in the pipeline is less than 0.04MPa should be used such as ZS, 2W, ZQDF, ZCM series and other direct-acting and step-by-step direct-acting; minimum operating pressure difference is greater than 0.04MPa can be used when the pilot type (pressure Differential type) Solenoid valve; the maximum working pressure difference should be less than the maximum calibration pressure of the solenoid valve; the general electromagnetic valve is one-way operation, so pay attention to whether there is back pressure difference, if there is a check valve installed.
When the fluid cleanliness is not high, the filter of Hongfeng valve factory should be installed in front of the solenoid valve. Generally, the electromagnetic valve requires better cleanliness of the medium.
Pay attention to the flow aperture and the nozzle diameter; solenoid valve is generally only two-way control switch; conditions allow to install the bypass pipe, easy to repair; have water hammer phenomenon to customize the solenoid valve opening and closing time adjustment.
Pay attention to the influence of the ambient temperature on the solenoid valve. The power supply current and power consumption should be selected according to the output capacity. The power supply voltage is generally allowed to be ±10%. It must be noted that the VA value at the time of AC start is high.
Second, reliability
Solenoid valves are classified into two types: normally closed and normally open; Normally selected are normally closed, energized open, and power off; however, normally open type is used when the open time is very long and closed.
When the operation time is very short, the direct-acting type is generally selected, and the large-caliber selection is used for the fast series.
Third, security
General solenoid valve is not waterproof, please use waterproof type when conditions do not allow, factory can be customized.
The highest rated pressure of the solenoid valve must exceed the maximum pressure in the pipeline, otherwise the service life will be shortened or other unexpected situations will occur.
Corrosive liquids should be made of all-stainless steel type, and strong corrosive fluids should use plastic king (SLF) solenoid valves.
Explosion-proof products must be selected for explosive environments.
Fourth, economy
There are many solenoid valves that can be used universally, but the most economical product should be chosen based on the above three points.
One: Applicability
The fluid in the tubing must match that of the media in the selected solenoid valve model.
The temperature of the fluid must be less than the calibrated temperature of the selected solenoid valve.
Solenoid valves allow the viscosity of liquids to be generally below 20CST, and should be indicated when more than 20CST.
Working pressure difference, the maximum pressure difference in the pipeline is less than 0.04MPa should be used such as ZS, 2W, ZQDF, ZCM series and other direct-acting and step-by-step direct-acting; minimum operating pressure difference is greater than 0.04MPa can be used when the pilot type (pressure Differential type) Solenoid valve; the maximum working pressure difference should be less than the maximum calibration pressure of the solenoid valve; the general electromagnetic valve is one-way operation, so pay attention to whether there is back pressure difference, if there is a check valve installed.
When the fluid cleanliness is not high, the filter of Hongfeng valve factory should be installed in front of the solenoid valve. Generally, the electromagnetic valve requires better cleanliness of the medium.
Pay attention to the flow aperture and the nozzle diameter; solenoid valve is generally only two-way control switch; conditions allow to install the bypass pipe, easy to repair; have water hammer phenomenon to customize the solenoid valve opening and closing time adjustment.
Pay attention to the influence of the ambient temperature on the solenoid valve. The power supply current and power consumption should be selected according to the output capacity. The power supply voltage is generally allowed to be ±10%. It must be noted that the VA value at the time of AC start is high.
Second, reliability
Solenoid valves are classified into two types: normally closed and normally open; Normally selected are normally closed, energized open, and power off; however, normally open type is used when the open time is very long and closed.
When the operation time is very short, the direct-acting type is generally selected, and the large-caliber selection is used for the fast series.
Third, security
General solenoid valve is not waterproof, please use waterproof type when conditions do not allow, factory can be customized.
The highest rated pressure of the solenoid valve must exceed the maximum pressure in the pipeline, otherwise the service life will be shortened or other unexpected situations will occur.
Corrosive liquids should be made of all-stainless steel type, and strong corrosive fluids should use plastic king (SLF) solenoid valves.
Explosion-proof products must be selected for explosive environments.
Fourth, economy
There are many solenoid valves that can be used universally, but the most economical product should be chosen based on the above three points.
Wall Fan,Wall Mounted Fan,Wall Exhaust Fan,Small Wall Fan
B&B EC CO., Ltd. , https://www.hi-cfm.com