IGBT Induction Heating Machine for Metal Forging Annealing

IGBT Induction Heating Machine for Metal Forging Annealing

Annealing (tempering and modulation):
1. Annealing of various stainless steel products,such as stainless steel basin, annealed and extruded can, stainless steel tube, tableware and cup.
2. Annealing of various other metal work pieces,
such as golf ball head, hardware copper fitting, aluminum radiator and various aluminum products.

More Application for the induction heating machine:

1, Brazing: it can be used for the brazing of various hardware cutting tools, diamond tools including diamond circular saw from diameter 300-2500mm, abrasive tool, drilling tool, alloy saw blade, hard alloy cutter, milling cutter, reamer, planning tool and solid center bit etc. It is suitable to used for the brazing of circular saw and other tools, usually 9 to 15 seconds is needed to braze one diamond blade.
2, Heat treatment: heat treatment of small parts
3, Melting: Melting below 2KG for gold, sliver, copper, brass, steel and iorn etc4,Forging,
5, Hardening
6, quenching
7,Annealing

Main characteristics:
1, MOSFET and Inverting technologies of First generation been used;
2, Simple structure and light weight;
3, Simple to operate, A few minutes is enough to learn it;
4, Simple to install, Installation can be done by unprofessional person very easily;
5, Advantages of the model with timer: The power and the operating time of the heating period and the retain period can be preset respectively, to realize a simple heating curve, this model is suggested to use for batch production to improve the repeatability;

Installing Desire
1, power supply wire: 6mm2 soft copper; Ground wire 4mm2 soft copper;
2, cooling water desire: Clean and not easy to scale, Inlet water temperature 25-36degree';
3, cooling water systerm: Running water; Circulating water from a pump to a tank; Use an industry refrigerate machine

.

Some application exeample 







 

 

Water/Wet type wire drawing machine

LT23-25/288 water tank wire drawing machine
(1) Main technical parameters:
1. Maximum incoming line strength: ≤ 1400Mpa;
2. Drawing passes: 23, 25;
3. Maximum incoming wire diameter: 1mm;
4. Minimum outlet diameter: 0.1-0.12mm;
5. Maximum drawing speed: 15m/s;
6. Average pass compression ratio: 14%;
7. Motor power: 15-18.5kw.
(2) Equipment composition for wet wire drawing machine
1. The frame is formed by welding section steel, and the tank body is formed by welding stainless steel plate;
2. The tower wheel is made of 45 steel, the working surface is sprayed with tungsten carbide powder (WC), the surface hardness is ＞ HRC60, the surface finish is 0.4Ra, and the service life is more than two years;
3. The machine coefficient is large in the front and small in the rear, which is conducive to improving production efficiency and continuous production;
4. Both the mold base and the mold base have angles, and the steel wire is always in a straight line during drawing, which is conducive to improving the quality and not easy to break the wire;
5. Tower wheel and mold are cooled by immersion in self circulating lubricating coolant;
6. The transmission mode is driven by synchronous belt to eliminate oil leakage and reduce noise;
7. The main bearings are made of NSK brand from Japan, and the motors are frequency conversion motors;
8. The finished product mold is installed in the mold base that can adjust the angle, which is conducive to the alignment of the finished product reel and the adjustment of the product ring diameter;
9. Box overturning force ≤ 200N;
10. All wire passing wheels and rollers are subject to quenching treatment, with surface hardness ＞ HRC50;
11. AC frequency conversion speed regulation is adopted, and the frequency converter adopts Siemens or Huichuan brand;
12. The electric control mode is PLC control, and the PLC is made of Mitsubishi or Siemens;
13. The touch screen is Taiwan made color touch screen, and low-voltage electrical components are all domestic well-known brands;
14. The machine is equipped with inching, front and rear linkage, start, stop and other functions. The human-machine interface of the main operating console has the functions of length, speed preset display, fault query, and equipment status display;
15. The electric cabinet is a standard cabinet produced by professional enterprises.

Water/Wet Type Wire Drawing Machine,Water Type Wire Drawing Machine,Wet Type Wire Drawing Machine,Water Tank Wire Drawbench

Jiangyin Wanyi Machinery CO.,Ltd , https://www.wydrawmachine.com