After compressing the docking garbage truck full of garbage, first open the scraper, and the slide board moves the scraper together to move downwards, piercing into the garbage for cracking and initial compression, and then the scraper is reversed forward to further compaction. Rubbish, the scraper is in place and then moves upwards with the skateboard, compacting the rubbish and loading it in the bin, and then returning to the starting position. The whole process takes the initiative to control, and when the garbage is continuously filled, the shovel pushes back under the effect of the extrusion force and gradually withdraws, completing the bidirectional compression of the garbage and filling the entire garbage can on average. When the compression-type butt-type garbage truck unloads the garbage at the disposal site, the loading device is lifted, the shovel is moved backwards, and the garbage in the garbage bin is pushed out along the degree.
The dustbin is made of reinforced beam and steel plate welded to form a strong frame structure. The bottom surface is a concave plane. The side surface and the top surface are arc surfaces. The appearance is beautiful, the weight is light, the force is good, and the deformation is not; the shovel is made of steel pipe skeleton and folded. The panel is composed of not only lightweight, but also can make the waste spread evenly, and the unloading is clean and thorough; the filling device is mainly composed of components such as the filler shell, slide plate and scraper, and each component adopts a beam plate or box type with superior force. Structure, strong structure, light weight. Garbage is in the form of a blockade during compression loading and transportation. The interface between the waste bin and the filler is sealed with a special rubber seal. The front end of the waste bin has a recovery tank consisting of a dustbin and a pusher shovel. Its volume is 1.35 m. There is a recovery tank with a volume of 0.3m in the lower part of the filling device, and the water receiving port can receive the sewage leaked due to the aging or damage of the sealing strip between the waste container and the filling device during the application process. The cylinder of the recovery tank device is controlled An artificially controlled drain valve facilitates the discharge of sewage at designated locations. The filler cap completely conceals the filling inlet of the filler, eliminating the disturbance of the flow of traffic in the rear of the vehicle and creating a dusty and dusty appearance. It is even more aesthetically pleasing.
In the hydraulic system of the lifting and filling device, an explosion-proof valve is provided. The valve separates the direct connection between the lifting cylinder and the hydraulic hose. Even if the fuel pipe bursts, the filling device will not suddenly fall into a vicious state and improve the use of safety. Sex. Each organization's mission has two active and manual operations. For example, the compression-type butt-type garbage trucks have active operation problems. Manual operations can be used to complete the organization's homework and unload the garbage. This not only covers the high-efficiency tasks of the garbage truck, but also provides debugging services. , maintenance and treatment of defects provide great convenience. The engine power output control, that is throttle restraint, can be fully controlled by the electrical system. It meets the power requirements of the garbage compaction cycle and pushing and unloading. Under other operating conditions, the initiator is actively in idle mode, which can reduce power consumption. And the incidence of illness, reduce fuel consumption, and improve economic efficiency. Finally, Xiao Bian reminded everyone when choosing a sealed docking garbage truck. Manufacturers can also make adjustments to the overturning bucket according to the customer's method of collecting garbage. This is also more conducive to customers' future use.
Ganland tie-down assemblies fill a wide variety of material handling and load restraint needs on transportation equipment, as well as in industrial fields for a variety of uses. Include lashing ring D-Rings & D-Ring tie downs. All Tie Down Rings are made from high quality material and trained expertise for multiple applications. These D-Ring tie downs are commendably durable and are popular among our customers for their long life and good performance. Ganland Lashing Rings are supplied for rich choice, including but not limited to construction: 304 grade stainless steel, steel, mild steel. Finish: polished, galvanized, zinc plated, zinc plating-coloring. Installation: weld on or bolt on. Different size, thickness and lengths. Thank you for considering Ganland for your next purchase, if you are searching for truck / trailer spare parts don`t forget to check our extensive range, high quality and competitive price, OEM and ODM, welcome.
Tie Down Rings
Tie Down Rings,Recessed Tie Down Rings,Lashing Rings,Rope Hook Rings
Jiaxing Ganland Auto Parts Co., Ltd. , https://www.ganlandparts.com